Buy or Renew
Buy or Renew
Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
2093034members
1438835discussions

Trending Topics

Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!

Community Activity

Start a conversation

VTP Status

Hi cisco Team,i have an switch 3560.. i want to become cisco part of client mode but its unable.. show vtp statusVTP Version capable : 1 to 3VTP version running : 1VTP Domain Name : am5.netVTP Pruning Mode : DisabledVTP Traps Generation : DisabledDev...

hamza-ali by • Level 1
  • 81 Views
  • 4 replies
  • 0 Helpful votes

Nexus 6K series issue

Hi cisco team,I have an 6K series nexus switch. i connect one uplink to my nexus. but my newly deployed nexus switch is not reachable directly to my putty. even its nexus switch ip is not pingable on cmd  

hamza-ali by • Level 1
  • 778 Views
  • 22 replies
  • 0 Helpful votes

bgp session not established

Hi according photo neighbor 172.31.3.185 hold on idle but another neigob active and then idle shut or no shut neighbor have ping 172.31.3.185 change force update-source But not establish bgp session nxos version is  64bit 10.3.6.M 

bgp.png

Ftd integration with Umbrella

Please find attached diagram and let me know can i integrate my Ftd with Cisco UmbrellaNote-: Here my Ftd will act as a internal firewall and Cisco umbrella will not integrate with Meraki MX due to license limitation. Cisco Umbrella has dns advantage...

Vishal6_0-1755774763928.png
Vishal6 by • Level 3
  • 944 Views
  • 4 replies
  • 0 Helpful votes

C9500-32C-A interface enable fails

The CLI enable command for an interface is rejected on my switch.  I did not expect this, is it normal for this switch?  I am on IOS 17.12.05 Switch#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#inter...

Resolved! EIGRP METRIC CALCULATION

I have tunnel 100 and 200 running across Site A and B, with EIGRP configured on both tunnels. Tunnel 100 is sourced from e1/0 and tunnel 200 e1/1 on both sites. The bandwidth and delay of tunnel 100 has been configured to make sure that EIGRP calcula...

Barikuma_0-1756366914251.png
Barikuma by • Level 1
  • 115 Views
  • 2 replies
  • 1 Helpful votes

ASR 9010 Linecard problem

Hello Community.We have a ASR 9010 Chassis with IOS XR 7.11.2. Our RP is A9K-RSP5-TR.Our problem is linecards. We have two sets of LCs. A9K-4X100GE-TR and A9K-24X10GE-1G-TR. When we insert linecard in any slots, it will go to below state.Location    ...

AminK by • Level 1
  • 59 Views
  • 0 replies
  • 0 Helpful votes

Switch is not directly goes in global mode

Hello Team, I am using ISE as a TACACS server for switches authentication. When i try to login the switch using ssh with TACACS credentials, i am able to login successfully but after login i want to enter directly in enable mode without entering the ...

Load more