Arduino UNO and SPI eeprom (AT93C46D)

Question

I'm trying to write to and read from an AT93C46D eeprom using an Arduino UNO but for some reason the output I'm getting is not what I expect.

The eeprom has a data structure of 128 words of 8 bits each and I'm trying to write 10000010 to each word. When reading back the data however I get 11000001. When I write 00000000 to all words I get 10000000 for all words when reading. I tested my code on 2 AT93C46D eeproms and both gave the same result.

It looks like the MSB is always 1 (when reading) for some reason.

I'm probably making a stupid mistake but I can't seem to find it, any help is greatly appreciated!

Datasheet: http://www.atmel.com/images/atmel-5193-seeprom-at93c46d-datasheet.pdf

#include<SPI.h>
#define DATAOUT 11//MOSI
#define DATAIN  12//MISO 
#define SPICLOCK  13//sck
#define SS 10//ss


void setup()
{
  pinMode(SS,OUTPUT);
  pinMode(DATAOUT, OUTPUT);
  pinMode(DATAIN, INPUT);
  pinMode(SPICLOCK,OUTPUT);
  digitalWrite(SS,LOW);

  Serial.begin(9600);

  SPI.beginTransaction(SPISettings(2000000, MSBFIRST, SPI_MODE0));

  fill();

  dump();
}

void loop()
{

}

void fill()
{
  Serial.println("Send EWEN opcode");
  digitalWrite(SS,HIGH);
  SPI.transfer(B10011); //EWEN
  SPI.transfer(B0000000);
  digitalWrite(SS,LOW);

  delay(100);

  for (int i=0; i < 128; i++) {
    digitalWrite(SS,HIGH);
    SPI.transfer(B101);
    SPI.transfer(i);
    SPI.transfer(B10000010);
    delay(10);
    digitalWrite(SS,LOW);
  }

  delay(100);

  Serial.println("Send EWDS opcode");
  digitalWrite(SS,HIGH);
  SPI.transfer(B1000); //EWDS
  SPI.transfer(B00000000);
  digitalWrite(SS,LOW);

  delay(10);
}

void dump(){
  Serial.println("Dumping AT93C46D");

  byte b;

  for (int i=0; i < 128; i++) {
    digitalWrite(SS,HIGH);
    SPI.transfer(B110); //read opcode
    SPI.transfer(i);
    b = SPI.transfer(B00000000); //clock data out
    digitalWrite(SS,LOW);
    Serial.println(b, BIN);
  }
}

Answer 1

After looking at the product spec again I think it might be possible to get this working. The protocol is MSB with a start bit S followed by two bit op-code, and parameters. SPI on AVR is 8-bit transfer but transfer can be byte aligned with the start bit.

READ is op-code(10) followed by 7-bit address, a dummy bit and the read value. That is in total 11+8-bits. Mapping that to 8-bit transfer would be:

spi.transfer(0b110);
spi.transfer(addr << 1);
data = spi.transfer(0);

That will give 5-bit zero, start-bit, op-code in the first transfer, and followed by 7-bit address and dummy bit (LSB) in second transfer. The third transfer is the read data.

EWEN would map to:

spi.transfer(0b1001);
spi.transfer(0b10000000);

EWEN has op-code(00), followed by 9-bits, 0b11XXXXXXX.

The WRITE operation becomes:

spi.transfer(0b10);
spi.transfer(0x80 | addr);
spi.transfer(data);

Cheers!